Ukratko
A hydraulic cylinder's force is the oil pressure times its effective (piston) area. In site units, force in kN = pressure in bar × area in cm² ÷ 100, times the number of identical cylinders on the pump. You can't turn bar into kN without the area: bar is a pressure and kN is a force, so the same gauge reading gives a different force on every cylinder. 400 bar is 100.4 kN on a 25.1 cm² cylinder and 204.8 kN on a 51.2 cm² one.
Pressure to force calculator
The physics in one line
F = p × A
- F is the force, p the oil pressure and A the cylinder's effective area: the area the oil pushes on.
- 1 bar = 100,000 Pa = 0.1 N/mm², and 1 cm² = 100 mm².
- So 1 bar on 1 cm² is 0.1 N/mm² × 100 mm² = 10 N, which is 0.01 kN.
That gives the rules in the table below. The other way round, the pressure for a force is bar = kN × 100 ÷ cm².
Force from the units you have
| You have | Force |
|---|---|
| bar and cm² | kN = bar × cm² ÷ 100 |
| bar and mm² | kN = bar × mm² ÷ 10,000 |
| MPa and mm² | kN = MPa × mm² ÷ 1,000 |
| psi and in² | lbf = psi × in²; kN = lbf ÷ 224.81 |
More than one cylinder on one pump
Cylinders on the same pump and hoses all see the same pressure. If they are identical, the total force is one cylinder's force times the number of cylinders:
kN = bar × cm² × number of cylinders ÷ 100
Two identical 25.1 cm² cylinders at 250 bar give 250 × 25.1 × 2 ÷ 100 = 125.5 kN between them. For 100 kN in total on the same pair you need 100 × 100 ÷ (25.1 × 2) = 199 bar.
A wrong number of cylinders gives a wrong force, just as a wrong area does: entering 1 when there are 2 shows half the real force, so you would pump to twice the force you meant.
Worked examples: Staht's own cylinders
| Cylinder | Effective area | At 700 bar (rated) | Pressure for 100 kN |
|---|---|---|---|
| Staht 18 t, 51 mm stroke | 25.1 cm² (2,510 mm²) | 700 × 25.1 ÷ 100 = 175.7 kN | 100 × 100 ÷ 25.1 = 398 bar |
| Staht 36 t, 51 mm stroke | 51.2 cm² (5,120 mm²) | 700 × 51.2 ÷ 100 = 358.4 kN | 100 × 100 ÷ 51.2 = 195 bar |
Other cylinders (illustrative areas)
| Effective area | Gauge reads | Force |
|---|---|---|
| 20 cm² | 500 bar | 500 × 20 ÷ 100 = 100 kN |
| 30 cm² | 500 bar | 500 × 30 ÷ 100 = 150 kN |
| 50 cm² | 400 bar | 400 × 50 ÷ 100 = 200 kN |
Use the effective area, not the outside size
Rounded, Staht's two cylinders give their published ratings of 176 kN and 358 kN. The areas in the second table are illustrative numbers chosen to show the method, not any maker's figures: use your own cylinder's published area.
A hollow cylinder (hollow ram) has a hole through the middle, so the area the oil pushes on is a ring inside the cylinder, not a disc. Staht's 18 t cylinder is 94 mm across the outside with a 26 mm bore. A disc 94 mm across, less the 26 mm hole, would be about 64 cm², but the published piston area is 25.1 cm². Working from the outside would overstate the force about two and a half times.
Always use the effective area the maker publishes, usually on the data sheet or the cylinder's plate.
Converting units
| From | To | Multiply (×) or divide (÷) by |
|---|---|---|
| kN | lbf | × 224.81 |
| kN | tonnes-force (metric) | ÷ 9.80665 |
| kN | US tons-force (2,000 lbf) | ÷ 8.896 |
| bar | psi | × 14.504 |
| bar | MPa | ÷ 10 |
| in² | cm² | × 6.4516 |
So 100.4 kN is about 22,571 lbf, 10.24 tonnes-force or 11.29 US tons. A "tonne" on a cylinder usually means metric tonnes-force, but a US maker's "ton" may be 2,000 lbf: check the data sheet. Staht's "18 t" cylinder is 176 kN ÷ 9.80665 ≈ 17.9 tonnes-force.
How gauge accuracy carries into force
A gauge accurate to a percentage of full scale has the same possible error, in bar, at every reading. Multiply that error by the area, and by the number of cylinders, to get it in kN.
The Staht G1 Pro is accurate to 0.25% of its 1000 bar full scale: ±2.5 bar at any reading. As a share of the reading that is 0.36% at 700 bar, 0.71% at 350 bar, 1.25% at 200 bar and 6.25% at 40 bar, so a low pressure on a large cylinder is where the error matters.
The G1 Pro's possible error, as force
| Cylinder | Possible error in force | On a 100 kN reading | Error is 10% of the reading at | Error is 5% of the reading at |
|---|---|---|---|---|
| 25.1 cm² (Staht 18 t) | ±2.5 × 25.1 ÷ 100 = ±0.63 kN | ±0.63% | 6.3 kN | 12.6 kN |
| 51.2 cm² (Staht 36 t) | ±2.5 × 51.2 ÷ 100 = ±1.28 kN | ±1.28% | 12.8 kN | 25.6 kN |
The bigger the cylinder, the bigger the error in kN, so a large cylinder is a poor choice for a small force. The gauge is only part of the picture:
- Seal friction. A cylinder's seals take a little of the force, so the delivered force can be slightly less than pressure × area.
- The area figure. The force is only as good as the area you use.
- Calibrating the gauge and cylinder together against a load cell covers both.
For anchor and rebar tests, our guide to pull tester gauge accuracy explains the 10% and 5% figures used on site.
What pressure gives my force?
Let the app do the sum
The Staht G1 Pro reads up to 1000 bar. Its own colour screen shows the pressure in bar, live and peak, and it sends the pressure over Bluetooth to the free Staht Connect app, which does the sum for you:
- Choose the cylinder, from your company's saved cylinders or Staht's own, or add any make by brand, part number, piston area and capacity.
- Set the number, from 1 to 10 identical cylinders.
- Confirm before every test. You tick two boxes, confirming the area and the number; the test can't start until both are ticked.
- Watch the force in kN or lbf beside the pressure, with a live graph, a target line and a countdown for the hold.
- Save the result, with Pass or Fail, the peak, photos and GPS location, synced to the web dashboard for reports and CSV.
See how it compares with other digital hydraulic pressure gauges.
Questions
No. You need the cylinder's effective area. 400 bar is 100.4 kN on a 25.1 cm² cylinder and 204.8 kN on a 51.2 cm² one.
1 bar is 0.1 N per square millimetre, and 1 cm² is 100 mm². So 0.1 × 100 = 10 N, or 0.01 kN.
Work out the force in kN (bar × cm² ÷ 100), then divide by 9.80665 for metric tonnes-force. 400 bar on a 25.1 cm² cylinder is 100.4 kN, or 10.24 tonnes-force.
Usually it means metric tonnes-force: 1 tonne-force is 9.80665 kN. A US maker's ton may be 2,000 lbf, which is 8.896 kN. Check the data sheet.
Yes. For 100 kN you need about 398 bar on Staht's 18 t cylinder (25.1 cm²) but only about 195 bar on the 36 t (51.2 cm²).
Yes. Under each calculator is the code to copy into your page. It shows the calculator with a link back to this page.
Sources
- Staht G1 Pro gauge user manual, Revision 1, 04/02/2026, Staht
- Staht Heavy Duty Test Kit brochure: Calibrated 1000 Bar Digital Pressure Gauge, UKAS Traceable, Accurate to 0.25% FS, Staht
- Staht 18 t cylinder, Technical Datasheet No 186: 25.1 cm² piston area, 700 bar, 176 kN, Staht
- Staht 36 t cylinder, Technical Datasheet No 187: 51.2 cm² piston area, 700 bar, 358 kN, Staht
- Rebar and holding-down bolt pull-out testing: piston areas, 175.7 kN and 358.4 kN at 700 bar, Staht
- The International System of Units (SI): 1 bar = 10⁵ Pa; standard gravity 9.80665 m/s², BIPM
Pressure on the gauge, force in the app
The G1 Pro reads to 1000 bar, and the free Staht Connect app shows the force for 1 to 10 cylinders of any make.
