Guide and calculator

Hydraulic pressure to force

Kısaca

A hydraulic cylinder's force is the oil pressure times its effective (piston) area. In site units, force in kN = pressure in bar × area in cm² ÷ 100, times the number of identical cylinders on the pump. You can't turn bar into kN without the area: bar is a pressure and kN is a force, so the same gauge reading gives a different force on every cylinder. 400 bar is 100.4 kN on a 25.1 cm² cylinder and 204.8 kN on a 51.2 cm² one.

Hydraulic cylinders

Pressure to force calculator

The unit your gauge reads in.

The pressure your gauge shows, in the unit chosen above.

Pick one of Staht's cylinders, or choose to enter your own cylinder's effective area below.

Used only with "Enter the area myself". The effective (piston) area from the cylinder maker's data sheet or plate. For a hollow ram it is much smaller than the outside size suggests.

The unit of the area above.

Identical cylinders on the same pump, so all at the same pressure. The Staht Connect app takes 1 to 10.

The highest working pressure on the cylinder's data sheet. Staht's 18 t and 36 t cylinders are rated to 700 bar.

From the gauge's data sheet or calibration certificate, as a percentage of full scale. The Staht G1 Pro is 0.25% of full scale.

The top of the gauge's scale. The G1 Pro's full scale is 1000 bar.

Sonuçlar

Pressure in bar400,0 bar
Effective area25,10 cm²
Number of cylinders1Whole numbers only.
Force100,40 kNPressure × area × number of cylinders: kN = bar × cm² × n ÷ 100.
Force in pounds-force22.571 lbf
Force in tonnes-force10,24 tfMetric tonnes-force: 1 tf = 9.80665 kN.
Force in US tons11,29 US tons1 US ton-force = 2,000 lbf = 8.896 kN.
Gauge's possible error, as force0,63 ± kNThe gauge's error in bar, the same at every reading for a full-scale accuracy, times the area.
The error as a share of this reading0,6 %

Force = pressure × the cylinder's effective area × the number of identical cylinders on the pump. In site units: kN = bar × cm² × n ÷ 100. Use the effective area the cylinder's maker publishes, not one worked out from the outside of the cylinder.

The result is the force the oil pressure makes. Seal friction means the delivered force can be slightly less, so for the closest figure calibrate the gauge and cylinder together.

The calculator works out force. It doesn't set test or working loads, and it doesn't replace the cylinder maker's data or the instructions of the engineer responsible for the job.

The figures shown when the page opens are an example: 400 bar on a Staht 18 t cylinder.

The Staht G1 Pro gauge reads up to 1000 bar. The free Staht Connect app shows the force in kN for 1 to 10 cylinders of any make, after you confirm the area and the number.

Bu hesaplayıcıyı web sitenize ekleyin

Bu kodu sayfanıza kopyalayın. Hesaplayıcıyı, bize bir bağlantıyla birlikte gösterir.

The physics in one line

F = p × A

  • F is the force, p the oil pressure and A the cylinder's effective area: the area the oil pushes on.
  • 1 bar = 100,000 Pa = 0.1 N/mm², and 1 cm² = 100 mm².
  • So 1 bar on 1 cm² is 0.1 N/mm² × 100 mm² = 10 N, which is 0.01 kN.

That gives the rules in the table below. The other way round, the pressure for a force is bar = kN × 100 ÷ cm².

Force from the units you have

You haveForce
bar and cm²kN = bar × cm² ÷ 100
bar and mm²kN = bar × mm² ÷ 10,000
MPa and mm²kN = MPa × mm² ÷ 1,000
psi and in²lbf = psi × in²; kN = lbf ÷ 224.81

More than one cylinder on one pump

Cylinders on the same pump and hoses all see the same pressure. If they are identical, the total force is one cylinder's force times the number of cylinders:

kN = bar × cm² × number of cylinders ÷ 100

Two identical 25.1 cm² cylinders at 250 bar give 250 × 25.1 × 2 ÷ 100 = 125.5 kN between them. For 100 kN in total on the same pair you need 100 × 100 ÷ (25.1 × 2) = 199 bar.

A wrong number of cylinders gives a wrong force, just as a wrong area does: entering 1 when there are 2 shows half the real force, so you would pump to twice the force you meant.

Worked examples: Staht's own cylinders

CylinderEffective areaAt 700 bar (rated)Pressure for 100 kN
Staht 18 t, 51 mm stroke25.1 cm² (2,510 mm²)700 × 25.1 ÷ 100 = 175.7 kN100 × 100 ÷ 25.1 = 398 bar
Staht 36 t, 51 mm stroke51.2 cm² (5,120 mm²)700 × 51.2 ÷ 100 = 358.4 kN100 × 100 ÷ 51.2 = 195 bar

Other cylinders (illustrative areas)

Effective areaGauge readsForce
20 cm²500 bar500 × 20 ÷ 100 = 100 kN
30 cm²500 bar500 × 30 ÷ 100 = 150 kN
50 cm²400 bar400 × 50 ÷ 100 = 200 kN

Use the effective area, not the outside size

Rounded, Staht's two cylinders give their published ratings of 176 kN and 358 kN. The areas in the second table are illustrative numbers chosen to show the method, not any maker's figures: use your own cylinder's published area.

A hollow cylinder (hollow ram) has a hole through the middle, so the area the oil pushes on is a ring inside the cylinder, not a disc. Staht's 18 t cylinder is 94 mm across the outside with a 26 mm bore. A disc 94 mm across, less the 26 mm hole, would be about 64 cm², but the published piston area is 25.1 cm². Working from the outside would overstate the force about two and a half times.

Always use the effective area the maker publishes, usually on the data sheet or the cylinder's plate.

Converting units

FromToMultiply (×) or divide (÷) by
kNlbf× 224.81
kNtonnes-force (metric)÷ 9.80665
kNUS tons-force (2,000 lbf)÷ 8.896
barpsi× 14.504
barMPa÷ 10
in²cm²× 6.4516

So 100.4 kN is about 22,571 lbf, 10.24 tonnes-force or 11.29 US tons. A "tonne" on a cylinder usually means metric tonnes-force, but a US maker's "ton" may be 2,000 lbf: check the data sheet. Staht's "18 t" cylinder is 176 kN ÷ 9.80665 ≈ 17.9 tonnes-force.

How gauge accuracy carries into force

A gauge accurate to a percentage of full scale has the same possible error, in bar, at every reading. Multiply that error by the area, and by the number of cylinders, to get it in kN.

The Staht G1 Pro is accurate to 0.25% of its 1000 bar full scale: ±2.5 bar at any reading. As a share of the reading that is 0.36% at 700 bar, 0.71% at 350 bar, 1.25% at 200 bar and 6.25% at 40 bar, so a low pressure on a large cylinder is where the error matters.

The G1 Pro's possible error, as force

CylinderPossible error in forceOn a 100 kN readingError is 10% of the reading atError is 5% of the reading at
25.1 cm² (Staht 18 t)±2.5 × 25.1 ÷ 100 = ±0.63 kN±0.63%6.3 kN12.6 kN
51.2 cm² (Staht 36 t)±2.5 × 51.2 ÷ 100 = ±1.28 kN±1.28%12.8 kN25.6 kN

The bigger the cylinder, the bigger the error in kN, so a large cylinder is a poor choice for a small force. The gauge is only part of the picture:

  • Seal friction. A cylinder's seals take a little of the force, so the delivered force can be slightly less than pressure × area.
  • The area figure. The force is only as good as the area you use.
  • Calibrating the gauge and cylinder together against a load cell covers both.

For anchor and rebar tests, our guide to pull tester gauge accuracy explains the 10% and 5% figures used on site.

Hydraulic cylinders

What pressure gives my force?

The force to reach, from the engineer responsible for the job or the test.

Pick one of Staht's cylinders, or choose to enter your own cylinder's effective area below.

Used only with "Enter the area myself". The effective (piston) area from the cylinder maker's data sheet or plate. For a hollow ram it is much smaller than the outside size suggests.

The unit of the area above.

Identical cylinders on the same pump, so all at the same pressure. The Staht Connect app takes 1 to 10.

The highest working pressure on the cylinder's data sheet. Staht's 18 t and 36 t cylinders are rated to 700 bar.

Sonuçlar

Effective area25,10 cm²
Number of cylinders1Whole numbers only.
Pressure needed398,4 barbar = kN × 100 ÷ (cm² × n).
Pressure in psi5.778 psi
Pressure in MPa39,84 MPa

Pressure = force ÷ (the cylinder's effective area × the number of identical cylinders). In site units: bar = kN × 100 ÷ (cm² × n).

The figures shown when the page opens are an example: 100 kN on one Staht 18 t cylinder.

Seal friction means a little more pressure may be needed for the same force. Keep within the rated pressure of the cylinder, the pump, the hose and the gauge.

Bu hesaplayıcıyı web sitenize ekleyin

Bu kodu sayfanıza kopyalayın. Hesaplayıcıyı, bize bir bağlantıyla birlikte gösterir.

Let the app do the sum

The Staht G1 Pro reads up to 1000 bar. Its own colour screen shows the pressure in bar, live and peak, and it sends the pressure over Bluetooth to the free Staht Connect app, which does the sum for you:

  • Choose the cylinder, from your company's saved cylinders or Staht's own, or add any make by brand, part number, piston area and capacity.
  • Set the number, from 1 to 10 identical cylinders.
  • Confirm before every test. You tick two boxes, confirming the area and the number; the test can't start until both are ticked.
  • Watch the force in kN or lbf beside the pressure, with a live graph, a target line and a countdown for the hold.
  • Save the result, with Pass or Fail, the peak, photos and GPS location, synced to the web dashboard for reports and CSV.

See how it compares with other digital hydraulic pressure gauges.

Questions

Sources

  1. Staht G1 Pro gauge user manual, Revision 1, 04/02/2026, Staht
  2. Staht Heavy Duty Test Kit brochure: Calibrated 1000 Bar Digital Pressure Gauge, UKAS Traceable, Accurate to 0.25% FS, Staht
  3. Staht 18 t cylinder, Technical Datasheet No 186: 25.1 cm² piston area, 700 bar, 176 kN, Staht
  4. Staht 36 t cylinder, Technical Datasheet No 187: 51.2 cm² piston area, 700 bar, 358 kN, Staht
  5. Rebar and holding-down bolt pull-out testing: piston areas, 175.7 kN and 358.4 kN at 700 bar, Staht
  6. The International System of Units (SI): 1 bar = 10⁵ Pa; standard gravity 9.80665 m/s², BIPM

Pressure on the gauge, force in the app

The G1 Pro reads to 1000 bar, and the free Staht Connect app shows the force for 1 to 10 cylinders of any make.

Sepetiniz

Sepetiniz yükleniyor…