Application

Turn your analogue hydraulic tester into a digital one

In breve

If your pump takes Staht's G1/4 quick connect fitting (802-020 or 802-021), keep your pump and cylinders and change the dial for a Staht G1 Pro digital Bluetooth gauge, reading up to 1000 bar. In the free Staht Connect app you pick your cylinder, any make, one to ten of them; confirm its area and the number before every test; and watch the force in kN live as you pump. Every test is saved with Pass or Fail, the peak, the graph, photos and its GPS location. For any other coupler, send us a photo and we'll tell you whether it can be connected, and with what.

The trouble with a dial

  • A dial gives you pressure, but the job asks for force. Someone reads a needle, finds the chart for that cylinder, converts the figure and writes it down.
  • Every step can go wrong: reading between divisions, using the wrong chart, copying the number badly.
  • The record is only as good as the notes. A test report needs the force, the cylinder and its piston area, and the pressure read.

Any cylinder, one to ten at a time

  • Add any make once, by its brand, part number, piston area and capacity, then choose from your company's saved cylinders or Staht's own.
  • Use several on one pump. Set how many identical cylinders the test uses, from 1 to 10, and confirm the number before every test.
  • A safety check before every test. A wrong area gives a wrong force, so the app asks you to tick two boxes, one for the cylinder's area and one for the number of cylinders. The test can't start until both are ticked.

How a test runs with the G1 Pro

  1. Fit the gauge with a G1/4 quick connect fitting: female (802-020) or male (802-021), steel, rated to 1000 bar, each with a seal washer and dust cap.
  2. Connect. Tap the Bluetooth button in Staht Connect and pick the G1 Pro from the testers nearby.
  3. Choose the cylinder and the number, then set the target, for example a force in kN held for 60 seconds.
  4. Tick the two safety boxes.
  5. Pump and watch. The gauge's colour screen shows the pressure in bar, live and peak. The app shows the force in kN beside the pressure, with a live graph, the target line and a countdown for the hold, and shows red if the force drops. Take photos as you go.
  6. Save. Release the pressure and tap once: the result shows Pass or Fail and the peak. Add a name, notes and your company's own fields, and file it in a folder.
  7. Report. The test syncs to the Staht web dashboard, with the cylinder, its area and the maximum pressure, to share or turn into a report or a CSV file.

Worked example

Two identical hollow cylinders, each with a piston area of 25.1 cm² (the figure for Staht's 18 t cylinder), are on one pump, and the gauge reads 250 bar.

Force = 250 × 25.1 × 2 ÷ 100 = 125.5 kN, about 12.8 tonnes-force.

With a dial you would read 250, look up the chart and double it. With the G1 Pro you confirm the cylinder's area and the number of cylinders in the app before the test, and the app works out the force. Check any figure in the pressure-to-force calculator.

What you get

  • Force in kN (or lbf), live, for 1 to 10 cylinders of any make.
  • A safety confirmation before every test.
  • A colour screen on the gauge, showing the pressure in bar, live and peak, with a peak hold that works without the app.
  • A timed hold, Pass or Fail, the peak, photos, GPS location and folders.
  • Reports and CSV from the web dashboard.
  • The Staht Connect app, free for G1 Pro buyers, with no subscription.
  • Accuracy of 0.25% of its 1000 bar full scale (±2.5 bar), UKAS traceable, calibrated for one year from purchase.
  • A heavy duty carry case and a USB-C charging cable.
  • Calibration by Staht: we calibrate pressure gauges up to 1000 bar, with UKAS traceable certificates.

Is my kit ready for it?

CheckWhat to look for
PressureYour working pressure is within the gauge's 1000 bar and within your cylinder's, pump's and hose's own ratings.
ConnectionThe G1 Pro has a G1/4 parallel thread and fits with Staht's G1/4 quick connect fittings (802-020 or 802-021). For any other coupler or gauge port, send us a photo and we'll tell you whether it can be connected, and with what.
Piston areaThe effective area the cylinder's maker publishes. Don't work it out from the outside: a hollow cylinder's working area is much smaller than its outside size suggests.
Number of cylindersUp to 10 identical cylinders on one pump, each with the area you enter.

Who it's for

  • Anyone with a hydraulic pump and cylinder, up to 1000 bar, who reads a dial and works out the force by hand.
  • Testing teams with hollow-cylinder anchor or rebar kits that read on a dial.
  • Anyone who sends us a gauge to calibrate: ask about going digital at the same time.

Questions

Make your hydraulic tester digital

The G1 Pro gauge and the free Staht Connect app: force from any cylinder, and a record of every test.

Il suo carrello

Caricamento del carrello…