Anchors and fixings hold up the things that keep people safe — fall-arrest eyebolts, scaffold ties, façade brackets, building services and temporary works. When an anchor fails, the consequences are rarely trivial. UK standards exist to make sure that the right anchor is selected, installed correctly, and verified by test where its performance cannot be assured by design and product data alone.
The word “pull test” is used loosely on site to describe several different procedures that answer different questions. Getting the distinction right matters: the wrong test produces the wrong evidence, and an installation that looks tested may not actually prove the duty being relied upon. This guide sets out the main regimes, when testing is required, and what good evidence looks like.
The code of practice for the selection and installation of post-installed anchors. Defines proof (test-load) testing to verify installation quality, and allowable load testing to establish capacity where design values don't apply.
Proof load typically up to 1.5× recommended load
Sampling guidance for how many anchors to test
Backed by the CFA Guidance Note on site testing
The code of practice for the design, selection, installation, use and maintenance of anchor devices used for personal fall protection. The 2019 revision covers system design, installation and inspection.
Post-install proof load of 6 kN for most anchor devices
Conforms to BS EN 795 anchor device types A–E
Periodic inspection by a competent person
The European product standard defining the type-test requirements and classes (A–E) for anchor devices. BS 7883 sits alongside it to govern installation and in-service inspection in the UK.
Defines anchor device classes A, B, C, D and E
Type-test performance requirements
Read together with PD CEN/TS 16415 for multi-user
The National Access & Scaffolding Confederation guidance for testing scaffold tie anchors. Sets required test loads and recording expectations for ties into brick, blockwork, concrete and other substrates.
Required vs achieved test load recording
Substrate-specific test expectations
Calibrated equipment and traceable records
Under BS 8539 the three procedures below answer different questions. Choosing the correct one is what turns a pull on an anchor into meaningful, defensible evidence.
| Test type | Question it answers | Destructive? | Typical use |
|---|---|---|---|
| Proof / test-load | Was this anchor installed correctly to a defined load? | No | ETA-approved anchors in known substrate — verifies installation quality |
| Allowable load | What safe working load can this anchor actually achieve? | Sometimes | Non-ETA materials or conditions outside the anchor's assessment |
| Ultimate / pull-out | At what load does this anchor or substrate fail? | Yes | Establishing or investigating resistance — will damage the substrate |
There is no single universal figure — sampling depends on the standard, the anchor, the substrate and the project specification. The values below are widely used starting points; always confirm against the current standard and the specifier's requirements for your job.
| Context | Indicative sampling | Indicative proof load |
|---|---|---|
| BS 8539 proof testing | Commonly around 1 in 25 to 1 in 40 anchors | Up to ~1.5× the recommended (working) load |
| BS 7883 fall-protection anchor | Each installed anchor device proof tested | 6 kN for most devices (except cavity constructions) |
| NASC TG4 scaffold ties | Per the guidance and project spec | Required test load per substrate and design |
Under BS 8539, testing is not optional where anchor performance cannot be assured through design, product data and controlled installation alone. The requirement is driven by risk, not preference. Where an anchor with a relevant ETA is installed by competent, supervised installers in a known substrate, the code recognises that testing may not be needed. In practice, the situations below frequently tip an installation into mandatory verification.
Test when any of these apply
A test is only as useful as the record it leaves behind. Whatever the standard, an auditable, traceable record is what demonstrates compliance at handover and stands up if performance is ever questioned.
Capture on every test
Testing should be carried out by a competent person — someone with the training, knowledge and experience to select the correct test, operate calibrated equipment, interpret the result and record it correctly. The CFA Guidance Note that accompanies BS 8539 addresses tester competency directly, and BS 7883 requires inspection by a competent person for fall-protection anchors.
Anchor devices used for personal fall protection are subject to periodic inspection by a competent person under BS 7883, typically on a regular interval (commonly annually) and after any event that could affect the anchor. Always follow the manufacturer's instructions and the inspection regime set out in the standard and your risk assessment.
Yes. A proof load figure is only meaningful if the gauge applying and measuring it is in calibration. Records should reference the equipment used and its current calibration certificate — an out-of-calibration tester undermines the entire evidence chain.
No. A proof (test-load) test is non-destructive and verifies that an installed anchor sustains a defined load without unacceptable movement. A pull-out test loads the anchor to failure to establish or investigate resistance, and will damage the substrate. They answer different questions and produce different evidence.
BS 8539 is the code of practice for construction fixings — post-installed anchors in concrete and masonry holding up building elements and services. BS 7883 covers anchor devices specifically for personal fall protection (working at height), conforming to BS EN 795. Many sites need both depending on what the anchor is doing.
BS 7883 recommends a post-installation proof load of 6 kN for most anchor devices (other than in cavity constructions). This aligns with the dynamic force limits built into the wider personal fall protection equipment standards.
Sampling depends on the anchor, substrate and specification. Figures around 1 in 25 to 1 in 40 are commonly cited, with the test load typically up to about 1.5 times the recommended working load. Always confirm against the current standard and the project specifier.
Not always. Where an anchor with a relevant European Technical Assessment is installed by competent, supervised installers in a known substrate, the standard recognises testing may not be needed because performance is already assured. Testing becomes necessary when uncertainty exists — unknown substrates, refurbishment, or installation outside the ETA conditions.
A calibrated digital pull tester suited to the load range and anchor type, with appropriate bridges, adapters and reaction equipment. Staht manufactures BS-compliant digital pull testers with data logging and Bluetooth, supported by UK-based calibration.
Staht designs and manufactures BS-compliant digital pull testers with data logging, Bluetooth and UK-based calibration support. Talk to our team about the right setup for your testing.